Overdue Calibration Finder
For whoever is asked what the overdue gauge measured

Paste your calibration register. See every instrument that is overdue, and what it measured.

Overdue Calibration Finder reads your calibration register line by line for overdue, untraceable and out-of-tolerance instruments against ISO 9001 clause 7.1.5, ISO/IEC 17025, ISO 13485, IATF 16949 and AS9100. Paste your calibration register, one line per instrument. Every instrument comes back with its due date worked out: overdue, due before your audit, no interval or no traceable calibration recorded, and out of tolerance at the last calibration with no impact assessment on the product it measured, each with the ISO 9001, IATF 16949, AS9100, ISO 13485 or ISO/IEC 17025 clause behind it.

Check your own registerEight instruments free, no account. A published dictionary of 58 instrument classes and the clause text load with the page; every date is worked out in your browser.

What comes back: overdue and due before your audit, no traceable calibration, out of tolerance with no impact assessment recorded, each with the clause behind it.

Paste your register: asset ID, type, last calibration, interval. Nothing else is needed, and nothing leaves your browser until you save. No customer names, drawings or part numbers: the "used on" column takes a process or a product family.

Every date is shown with its arithmetic: last calibration plus interval gives the due date, against the date you set. Spot-check five instruments against your own register.

No email before the result and no score.

It never says an instrument is calibrated, accurate, fit for use or compliant, and never decides whether product was acceptable. A finding is a question for the quality manager.

Specimen, 4 of 40 labelsan invented machining company
overdue 198 days
MIC-0207
Micrometer
due 14/03/2026
14/03/2025 + 12 months
5 overdue in use
overdue 26 days
HG-0310
Height gauge
due 02/09/2026
02/09/2025 + 12 months
5 overdue in use
in date
TW-0520
Torque wrench
due 04/02/2027
04/08/2026 + 6 months
4 no impact assessment
due before audit
CMM-01
Coordinate measuring machine
due 05/11/2026
05/11/2025 + 12 months
6 lab not accredited

40 instruments, 4 overdue (2 used to accept product), 1 out of tolerance as found with no impact assessment recorded.

12 of 12 findings raised, 39 of 40 classes matched, 15 instruments on the recall sheet.

A laboratory technician in a hairnet, mask and gloves weighing a sample on an analytical balance
Walk into the surveillance audit already holding the answer to the auditor's first sampling question: which gauges ran past their dates, which lots they touched, and the clause for each. It works from the register spreadsheet you keep today, in your browser, with no calibration system to buy or install first.
01

Paste the register as it leaves the spreadsheet

One instrument per row: asset ID | type | last calibration | interval at least, or a header row with any of description, location, owner, due date, cal by, lab accredited, certificate number, traceable, as found, adjusted, used for acceptance, used on, status, procedure and impact assessment. Each instrument is matched to one of 58 published classes; one that fits none is read for its dates all the same.

02

Read the recall sheet and the arithmetic

Every due date is the last calibration plus the interval, calendar months added as months, printed beside the result. The recall sheet lays out what is overdue, what falls due before the audit date you set, and the next 90 days. A date that could be read day first or month first is shown both ways until you set the format.

03

Take the questions to the quality manager

Twelve findings in a fixed order, from overdue to a duplicate asset ID, each with the instruments it names, the clause from ISO 9001, IATF 16949, AS9100D, ISO 13485, ISO/IEC 17025, 21 CFR 211 or 21 CFR 58, and the question an auditor asks. The worksheet sets out the period in question for each out-of-tolerance or overdue acceptance gauge.

One instrument per row: Asset ID | Type | Last calibration | Interval, or a header row with any of Description, Location, Owner, Due date, Cal by, 17025 accredited, Cert no, Traceable, As found, Used for acceptance, Status, Procedure, Impact assessment. Tabs, pipes, commas or double spaces. A first line such as standards: IATF 16949, ISO 9001 | audit date: 2026-11-09 | date format: day first | as at: 2026-09-28 sets the rest.
Nothing is sent anywhere until you choose to save.
Standards that apply, and your dates (the first line of a paste sets them too)

Why a register, and not a calibration system

A calibration management system tracks instruments well once every one of them is in it. The quality manager at a 400-person shop is asked a simpler question first, by the certification body auditor, a customer or the board: across every gauge we hold, which are past due, which were used to accept product while past due or out of tolerance, and what did we decide about the parts they measured. The answer sits in the register you already keep. That is what this reads, in your browser, from the register as it stands.

The dictionary is ours and published in full: every instrument class and the clauses behind it, what each standard asks of a calibration register, the twelve findings, what the standards say about calibration intervals, what an auditor asks about overdue calibration and the calibration register template. It reads the register only; a finding is a question for the quality manager, never a ruling on an instrument or a product.

Overdue and untraceable instruments: the questions buyers ask

What does Overdue Calibration Finder do?

It reads your calibration register line by line and works out every instrument's due date, flagging the overdue, the untraceable and the out-of-tolerance. Each finding carries the clause behind it and the question an auditor asks.

Which standards does it cite?

ISO 9001 clause 7.1.5, ISO/IEC 17025, ISO 13485, IATF 16949 and AS9100D, plus 21 CFR Part 211 and 21 CFR Part 58 where you tick them. Each is read clause by clause from the published text.

What do I need to paste?

One instrument per row with asset ID, type, last calibration and interval. No customer names, drawings or part numbers are needed; the used-on column takes a process or a product family.

How is the due date worked out?

Every due date is the last calibration plus the interval, calendar months added as months, printed beside the result. That arithmetic is shown so you can spot-check five instruments against your own register.

What if a date could be day-first or month-first?

A date that could be read day first or month first is shown both ways until you set the format. The reading is then not silently assumed.

What is the recall sheet?

It lays out what is overdue, what falls due before the audit date you set, and the instruments due in the next 90 days. It is built from the dates in your own register.

Does it tell me an instrument is calibrated or fit for use?

No. It never says an instrument is calibrated, accurate, fit for use or compliant, and it never decides whether product was acceptable. A finding is a question for the quality manager.

Does it check whether a gauge was used to accept product while overdue?

Yes. The register can carry a used-for-acceptance column, and the findings and the worksheet set out the period in question for each out-of-tolerance or overdue acceptance gauge.

What does out of tolerance with no impact assessment mean?

It means an instrument found out of tolerance at its last calibration with no impact assessment recorded on the product it measured. It is one of the twelve findings.

How many instrument classes does it know?

A published dictionary of 58 instrument classes loads with the page. An instrument that fits none is still read for its dates all the same.

In what order are the findings?

Twelve findings in a fixed order, from overdue to a duplicate asset ID. Each names the instruments it concerns, the clause and the question an auditor asks.

Does it cost anything, and does my data leave my browser?

Eight instruments are free and no account is needed. Every date is worked out in your browser, with no email before the result and no score, and nothing leaves it until you save.

How Overdue Calibration Finder compares with the alternatives

A spreadsheet is better for holding the register and the certificates beside it, because it is free and already the place the dates live. A quality consultant or calibration laboratory is better on judgement, since tolerance, fitness for use and the effect of an out-of-tolerance result on product are their call, and a calibration management system is better once every instrument is loaded and tracked live. A general AI assistant is better at drafting an impact assessment or explaining a clause in general terms, but it does not work each due date out from last calibration plus interval and read it against the ISO 9001, IATF 16949, AS9100 and ISO/IEC 17025 clause text. The finder reads the register as it stands and returns the overdue, untraceable and out-of-tolerance instruments with the clause behind each and the arithmetic shown; it never says an instrument is calibrated, accurate or fit for use, and never decides whether product was acceptable.

Primary source: ISO 9001:2015